ICS TRIPLEX T3419自動化模塊備件,機械備件
不需要更換硬件EPROM。3.1.4鍵盤a）說明469條消息被組織成標題“設置點”和“實際值”下的頁面。該鍵在可編程參數頁面標題中導航。該鍵在測量參數頁面標題中導航。每個頁面進一步細分為消息的邏輯子組。和鍵可用于在子組中導航。關鍵是雙重目的。它用于輸入子組或存儲更改的設定值。關鍵也是雙重目的。它可用于退出子組或在存儲之前將更改的設定點返回到其原始值。和鍵在設定點編程模式下的變量和遞增/遞減數值設定值之間滾動?；蛘?，可以使用數字鍵盤輸入這些值。可以隨時按下該鍵以顯示上下文相關的幫助消息。b） 輸入字母文本要為特定應用定制469，可以在多個地方對自定義文本消息進行編程。一個例子是消息草稿。要輸入字母數字文本消息，應遵循以下步驟：例如，輸入文本“檢查液位”：1。按十進制鍵[.]進入文本編輯模式。2.按或鍵，直到出現C，然后按十進制鍵[.]以前進光標。3.對其余字符重復步驟2：h、e、c、k、F、l、u、i、d、l、e、v、e、l、s。4.按下可儲存文字信息。c） 輸入+/-符號469沒有“+”或“–”鍵。負數可以兩種方式之一輸入。?立即按下/鍵可使設定點在其范圍內滾動，包括任何負數。?在輸入至少一位數字設定值后，按下或鍵可更改值的符號（如適用）。設置點實際消息消息輸入退出值幫助值值輸入值值值GE Multilin 469電機管理繼電器3-3 3用戶接口3.1 FACEPLATE INTERFACE 3 3.1.5設置點輸入要存儲任何設置點，必須短接端子C1和C2（接入端子）（可使用鑰匙開關進行安全保護）。還有一個限制訪問設置點的設置點密碼功能。必須輸入密碼以允許更改設定值。密碼為0有效地關閉密碼功能——在這種情況下，更改設定點只需要訪問跳線。如果5分鐘內未按下任何鍵，將限制訪問設定值，直到再次輸入密碼。為防止在5分鐘內訪問設定點，可關閉并重新打開裝置，移除訪問跳線，或?qū)⒃O(shè)定點訪問設定點更改為“受限”。在端子C1和C2（接入端子）短路之前，無法輸入密碼。當允許訪問設定點時，469前部的設定點訪問LED指示燈將點亮。即使在電機運行時，設定值更改也會立即生效。但是，不建議在電機運行時更改設定值，因為任何錯誤都可能導致意外跳閘。以下程序可用于訪問和更改設定點。此特定示例指的是輸入
does not require a hardware EPROM change. 3.1.4 KEYPAD a) DESCRIPTION 469 messages are organized into pages under the headings Setpoints and Actual Values. The key navigates through the programmable parameters page headers. The key navigates through the measured parameters page headers. Each page is broken down further into logical subgroups of messages. The and keys may be used to navigate through the subgroups. The key is dual purpose. It is used to enter the subgroups or store altered setpoint values. The key is also dual purpose. It may be used to exit the subgroups or to return an altered setpoint to its original value before it has been stored. The and keys scroll through variables in the setpoint programming mode and increment/decrement numerical setpoint values. Alternately, these values may be entered with the numeric keypad. The key may be pressed at any time to display context sensitive help messages. b) ENTERING ALPHANUMERIC TEXT To customize the 469 for specific applications, custom text messages may be programmed in several places. One example is the Message Scratchpad. To enter alphanumeric text messages, the following procedure should be followed: For example, to enter the text "Check Fluid Levels": 1. Press the decimal key [.] to enter text editing mode. 2. Press the or keys until C appears, then press the decimal key [.] to advance the cursor. 3. Repeat step 2 for the remaining characters: h,e,c,k, ,F,l,u,i,d, ,L,e,v,e,l,s. 4. Press to store the text message. c) ENTERING +/– SIGNS The 469 does not have ‘+’ or ‘–’ keys. Negative numbers may be entered in one of two manners. ? Immediately pressing the / keys causes the setpoint to scroll through its range including any negative numbers. ? After entering at least one digit of a numeric setpoint value, pressing the or keys changes the sign of the value where applicable. SETPOINT ACTUAL MESSAGE MESSAGE ENTER ESCAPE VALUE VALUE HELP VALUE VALUE ENTER VALUE VALUE VALUE VALUE GE Multilin 469 Motor Management Relay 3-3 3 USER INTERFACES 3.1 FACEPLATE INTERFACE 3 3.1.5 SETPOINT ENTRY To store any setpoints, terminals C1 and C2 (access terminals) must be shorted (a keyswitch may be used for security). There is also a setpoint passcode feature that restricts access to setpoints. The passcode must be entered to allow the changing of setpoint values. A passcode of 0 effectively turns off the passcode feature – in this case only the access jumper is required for changing setpoints. If no key is pressed for 5 minutes, access to setpoint values will be restricted until the passcode is entered again. To prevent setpoint access before the 5 minutes expires, the unit may be turned off and back on, the access jumper may be removed, or the SETPOINT ACCESS setpoint may be changed to "Restricted". The passcode cannot be entered until terminals C1 and C2 (access terminals) are shorted. When setpoint access is allowed, the Setpoint Access LED indicator on the front of the 469 will be lit. Setpoint changes take effect immediately, even when motor is running. However, changing setpoints while the motor is running is not recommended as any mistake may cause a nuisance trip. The following procedure may be used to access and alter setpoints. This specific example refers to entering
