產品內容介紹
1400-PD51A電源監視器
數據區域大小的限制確定所有I/O模塊（即不包括電源和CPU模塊的模塊）提供的數據區域的總大小M。然后檢查M的值是否符合數據區域最大大小的限制。數據區M的總大小取決于I/O模塊的安裝順序。根據您的應用需求，提前考慮系統配置，包括子單元數量、單元編號和I/O模塊的安裝位置。z由于數據區域大小的限制定義為M≤ 112+32×（4-n），其中n=CPU模塊數。此處的值112和32是由于CPU模塊的功能規格而造成的限制。z計算程序按順序匯總所有I/O模塊的數據區域大小，從主機插槽1到第七個子單元插槽16，以確定總大小M。如果有數據區域大小為4、8或16的I/O模塊，則將數據區域大小的運行總數四舍五入到最接近的4、8和16的倍數，然后再添加該I/O模塊的大小。示例：如果系統配置了以下模塊，則總數據區域M為56。如果使用光纖FA總線類型2模塊將子單元劃分為組，則插槽總數可能會小于上述值，具體取決于此類劃分的模式。有關總金額計算的更多信息，請參閱光纖FA總線模塊和光纖FAbus 2型模塊、FA總線2型模塊（IM 34M06H45-01E）。數據區M的總大小取決于模塊的安裝順序。如果初始系統配置不符合任何給定限制，請嘗試通過串行安裝相同數據區域大小的I/O模塊來更改模塊的安裝順序。此策略可以實現對限制的遵從。
對于順序CPU模塊類型
確定分配給序列CPU模塊的I/O模塊提供的I/O點的總和R。然后檢查R的值是否符合最大I/O點數的限制。分配給CPU模塊的I/O模塊是指那些實際安裝并設置為Configuration（配置）菜單的Use（使用）選項的模塊。如果安裝了兩個或更多CPU模塊，請檢查每個模塊是否符合要求。z當CPU模塊為F3SP21 R時≤2048 z當CPU模塊為F3SP22/25/28/53/66/71或F3FP36 R時≤4096 z當CPU模塊為F3SP35/38/58/59/67/76 R時≤8192另見I/O模塊分配的詳細信息，請參閱梯形圖支持程序M3（IM 34M06Q13-01E）中的FA-M3編程工具WideField3（IM 34 M06Q16-xxE）、FA-M3程序工具WideField 2（IM 36 M06Q15-01E）、FA-M3編程工具WideFild（IM 39 M06Q14-01E）或第6.6節“輸入配置項目”。確定I/O模塊為分配I/O模塊的BASIC CPU模塊提供的工作區總數D。然后檢查D值是否符合BASIC CPU工作區大小的限制。分配給CPU模塊的I/O模塊是指那些由BASIC程序中的ASSIGN語句聲明其用途的模塊。在確定BASIC CPU工作區的總和D時要小心，因為工作區是十六進制的。z當CPU模塊為F3BP20或F3BP30 D時≤$2900值$2900受CPU模塊的功能規格限制。另請參閱“BASIC CPU modules and YM-BASIC/FA Programming Language”（IM 34M06Q22-01E）中的第B7.3節“I/O模塊使用聲明”，了解I/O模塊分配的詳細信息。
Restrictions due to the Size of Data Area
Determine the total size M of the data area provided by all I/O modules (i.e., modules excluding the power supply and CPU modules). Then check that the value of M complies with restrictions placed by the maximum size of data area. The total size of data area M varies depending on the order in which I/O modules are installed. Consider system configuration in advance, including the number of subunits, unit number and I/O modules’ installation locations, according to your application needs. z Restrictions due to the size of data area are defined as M ≤ 112 + 32 × (4 - n), where n = the number of CPU modules. The values 112 and 32 here are the limits due to the function specifications of the CPU modules. z Calculation Procedure Sum up the sizes of data areas in sequence for all I/O modules, starting from slot 1 of the main unit up to slot 16 of the 7th subunit to determine the total size M. If there is any I/O module with a data-area size of 4, 8 or 16, then round up the running total for the data area sizes to the nearest multiple of 4, 8 or 16 before you add the size of that I/O module. Example: If the system is configured with the following modules, the total data area M is 56. If subunits are divided into groups using fiber-optic FA-bus type 2 modules, the total number of slots may become smaller than the value noted above depending on the mode of such division. For more information on the calculation of the total sum, see the Fiber-optic FA-bus Module and Fiber-optic FAbus Type 2 Module, FA-bus Type 2 Module (IM 34M06H45-01E).The total size of data area M varies depending on the order in which modules are installed. If the initial system configuration fails to comply with any given restriction, try changing the order in which modules are installed by serially installing I/O modules of the same data-area size, for example. This strategy may achieve compliance with the restriction.
For Sequence CPU Module Type
Determine the total sum R of I/O points provided by I/O modules allocated to the sequence CPU module. Then check that the value of R complies with restrictions placed by the maximum number of I/O points. The I/O modules allocated to the CPU module refer to those that are actually installed and set to the Use option of the Configuration menu. If two or more CPU modules are installed, check each of them for compliance. z When the CPU module is F3SP21 R≤2048 z When the CPU module is F3SP22/25/28/53/66/71 or F3FP36 R≤4096 z When the CPU module is F3SP35/38/58/59/67/76 R≤8192 SEE ALSO For details on the allocation of I/O modules, see FA-M3 Programming Tool WideField3 (IM 34M06Q16- xxE), FA-M3 Programming Tool WideField2 (IM 34M06Q15-01E), FA-M3 Programming Tool WideField (IM 34M06Q14-01E) or Section 6.6, “Entering Configuration Items,” in the Ladder Diagram Support Program M3 (IM 34M06Q13-01E).Determine the total sum D of work areas provided by I/O modules for the BASIC CPU module to which the I/O modules are allocated. Then check that the value of D complies with restrictions due to the size of the BASIC CPU’s work area. The I/O modules allocated to the CPU module refer to those whose use is declared by the ASSIGN statement in the BASIC program. Be careful when determining the total sum D of the BASIC CPU’s work area since the work areas are in hexadecimal. z When the CPU module is F3BP20 or F3BP30 D≤$2900 The value $2900 is limited by the function specifications of the CPU module. SEE ALSO For details on the allocation of I/O modules, see Section B7.3, “Declaration of Use of I/O Modules” in the “BASIC CPU Modules and YM-BASIC/FA Programming Language” (IM 34M06Q22-01E).
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
