產品內容介紹
Schumacher 1483-0400A輸入流量控制器
外部輸入保護該裝置經過測試，可用于20A以下的分支電路。僅當供電支路的載流量大于此值時，才需要外部保護。在某些國家，當?shù)胤ㄒ?guī)可能適用。還應檢查當?shù)匾?guī)范和當?shù)匾?。如果需要或使用外部保險絲，則需要最小值以避免保險絲意外跳閘。并聯使用說明：單元A AC DC單元B AC DC-+-+負載+-A）僅使用同一系列（XLS）的電源。b） 將所有電源的輸出電壓調整至大致相同的值（±500mV）。否則，DC ok信號可能無法正常工作。c） 只有當三個以上的裝置并聯時，才需要在輸出端安裝保險絲（或二極管）。d） 不要給端子加載超過25A的電流。按照第27.9 e）節中的接線說明進行操作。兩個電源之間保持15mm（左/右）的安裝間隙，避免將電源安裝在彼此的頂部。當電源安裝在密封嚴密的外殼中時，外殼內部的溫度將高于外部。內部溫度定義電源的環境溫度。這種安裝的結果是：電源放在盒子的中間，盒子內沒有其他熱發生器
并行使用以實現冗余
電源可以并聯以實現冗余，以獲得更高的系統可用性。冗余系統需要一定數量的額外電源，以在一個電源設備發生故障時支持負載。最簡單的方法是將兩個XLS電源并聯。這稱為1+1冗余。如果一個電源裝置發生故障，另一個電源可自動支持負載電流而不會中斷。用于更高功率需求的冗余系統通常采用N+1方法構建。E、 g.五個電源并聯，每個額定值為10A，以構建40A冗余系統。請注意：這種構建冗余系統的簡單方法不包括諸如電源二次側內部短路之類的故障。在這種幾乎不可能的情況下，缺陷單元成為其他電源的負載，輸出電壓無法再維持。這只能通過使用解耦模塊1606-XLSRED中包含的解耦二極管來避免。構建冗余電源系統的建議：a）為每個電源使用單獨的輸入保險絲。b） 監控各個電源設備。單元中已包含直流ok指示燈和直流ok觸點。此功能報告單元故障。c） 如果可能，將每個電源連接到不同的相位或電路。d） 最好將所有電源的輸出電壓設置為相同的值，以避免錯誤的DC ok信號。27.9.只要通過一個端子引腳的最大電流不超過25A，就允許菊花鏈（從一個電源輸出跳到下一個）。如果電流較高，請使用單獨的配電接線板。
EXTERNAL INPUT PROTECTION
The unit is tested and approved for branch circuits up to 20A. External protection is only required if the supplying branch has an ampacity greater than this. In some countries local regulations might apply. Check also local codes and local requirements. If an external fuse is necessary or utilized, a minimum value is required to avoid undesired tripping of the fuse.Instructions for parallel use: Unit A AC DC Unit B AC DC - + - + Load + - a) Use only power supplies from the same series (XLS). b) Adjust the output voltages of all power supplies to approximately the same value (±500mV). Otherwise, the DC-ok signal might not work properly. c) A fuse (or diode) on the output is only required if more than three units are connected in parallel. d) Do not load terminals with more than 25A. Follow wiring instructions according to section 27.9 e) Keep an installation clearance of 15mm (left/right) between two power supplies and avoid installing the power supplies on top of each other.When the power supply is installed in a tightly sealed enclosure, the temperature inside the enclosure will be higher than outside. The inside temperature defines the ambient temperature for the power supply. Results from such an installation: Power supply is placed in the middle of the box, no other heat producer inside the box
PARALLEL USE FOR REDUNDANCY
Power supplies can be paralleled for redundancy to gain a higher system availability. Redundant systems require a certain amount of extra power to support the load in case one power supply unit fails. The simplest way is to put two XLS power supplies in parallel. This is called a 1+1 redundancy. In case one power supply unit fails, the other one is automatically able to support the load current without any interruption. Redundant systems for a higher power demand are usually built in a N+1 method. E.g. Five power supplies, each rated for 10A are paralleled to build a 40A redundant system. Please note: This simple way to build a redundant system does not cover failures such as an internal short circuit in the secondary side of the power supply. In such a - virtually nearly impossible - case, the defect unit becomes a load for the other power supplies and the output voltage can not be maintained any more. This can only be avoided by utilizing decoupling diodes which are included in the decoupling module 1606-XLSRED. Recommendations for building redundant power systems: a) Use separate input fuses for each power supply. b) Monitor the individual power supply units. A DC-ok lamp and a DC-ok contact is already included in the units This feature reports a faulty unit. c) When possible, connect each power supply to different phases or circuits. d) It is desirable to set the output voltages of all power supplies to the same value to avoid a false DC-ok signal. 27.9. DAISY CHAINING OF OUTPUTS Daisy chaining (jumping from one power supply output to the next) is allowed as long as the maximum current through one terminal pin does not exceed 25A. If the current is higher, use a separate distribution terminal block.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
