產品內容介紹
CUTLER HAMMER 5785T 92-02016-00終端控制模塊
輸入信號類型選擇每個輸入可以與電流或電壓信號一起使用。選擇由位于NAIO頂蓋后面的DIP開關制成模塊外殼（見圖3-1）。開關設置如下所示。獨立于信號類型的選擇模擬輸入以mA顯示在ACS 600控制面板上；e、 g.10 V將顯示為20 mA。必須考慮到這一點縮放信號或讀取模擬的實際值時輸入端AI2和AI3。有關更多信息，請參閱驅動器手冊。0.5至1.5 mm2雙絞線，單獨和/或整體模擬信號應使用屏幕。屏幕應為連接至NAIO模塊上的SHF端子。參見示例下圖。X1和X2具有單獨的RC濾波器，如上圖所示，即一個接線板上的SHF端子連接在一起，然后連接至通過RC濾波器接地。
注意：不要將信號電纜與電源電纜平行布線。
編程模塊和驅動器之間的通信由驅動參數。（確保參數設置與模塊的模式開關設置。）激活后，NAIO替換某些標準輸入和輸出。請參閱驅動器固件手冊，參數組98。
3.0及以下版本的標準應用程序用戶應參考
有關驅動參數列表，請參見附錄E。
注意：新設置僅在模塊下次通電。
NAIO模塊
替換NAIO-03可用于更換有故障的NAIO-01/02，NAIO類型的差異詳見附錄E.I/O擴展鏈路兼容設備：NAIO模塊、NDIO模塊、NTAC模塊、ACS 600變頻器
鏈路最大大小：128個站點
拓?fù)洌涵h(huán)形
串行通信類型：異步
傳輸速度：1 Mbit/s協議：ABB分布式驅動通信系統（DDCS）
介質訪問控制方法：
?ACS 600投票的應用和電機控制委員會（NAMC）其他車站周期性電纜：光纖電纜
?結構：塑料芯，直徑1mm，塑料護套夾克
?電纜衰減：0.23 dB/m
?電纜最大長度：兩站之間10 m外殼：塑料，尺寸：45 mm x 75 mm x 105 mm
防護等級：IP 20
安裝：安裝在標準安裝導軌上硬件設置：七個DIP開關用于設置節點編號。分配的節點號：16（默認）。
連接器：
?用于ACS 600連接
?兩個螺釘接線板（Phoenix Contact MVBSTW 2,5/8-ST5,08），用于編碼器和電源連接。導線橫截面積：0.5至2.5 mm2
Input Signal Type Selection
Each input can be used with a current or voltage signal. The selection is made with a DIP switch located behind the top lid of the NAIO module casing (see Figure 3-1). The switch settings are shown below.Independent of the selection of the signal type, the values of the analogue inputs are displayed in mA on the ACS 600 Control Panel; e.g. 10 V will be displayed as 20 mA. This must be taken into account when scaling the signals or reading the actual value of the analogue inputs AI2 and AI3. See the drive manuals for more information.0.5 to 1.5 mm2 twisted pair cables with individual and/or overall screens should be used for analogue signals. The screens should be connected to the SHF terminals on the NAIO module. See the example below.X1 and X2 have separate RC filters as pictured above, i.e. the SHF terminals on one terminal block are connected together, then to earth through an RC filter. Note: Do not route the signal cables parallel to power cables. Programming The communication between the module and the drive is activated by a drive parameter. (Ensure that the parameter settings correspond to the mode switch setting of the module.) After activation, the NAIO replaces certain standard inputs and outputs. See the drive Firmware Manual, Parameter Group 98. Users of Standard Application Program versions up to 3.0 should refer to Appendix E for a listing of related drive parameters. Note: The new settings take effect only the next time the module is powered up. NAIO Module Replacement An NAIO-03 can be used to replace a faulty NAIO-01/02. For reference, the differences of the NAIO types are detailed in Appendix E.
I/O Extension Link
Compatible Devices: NAIO module, NDIO module, NTAC module, ACS 600 frequency converter Maximum size of the link: 128 stations Topology: Ring Serial communication type: Asynchronous Transmission speed: 1 Mbit/s Protocol: ABB Distributed Drives Communication System (DDCS) Medium access control method: ? Application and Motor Control Board (NAMC) of the ACS 600 polls other stations cyclically Cable: Fibre optic cable ? Construction: Plastic core, diameter 1 mm, sheathed with plastic jacket ? Cable attenuation: 0.23 dB/m ? Cable maximum length: 10 m between two stations
Enclosure: Plastic, dimensions: 45 mm x 75 mm x 105 mm. Degree of protection: IP 20 Mounting: Onto a standard mounting rail Hardware settings: Seven DIP switches for setting the node number. Allocated node number: 16 (default). Connectors: ? Light transmitter and receiver (Hewlett-Packard Versatile Link) for ACS 600 connection ? Two screw terminal blocks (Phoenix Contact MVBSTW 2,5/8-ST5,08) for encoder and power supply connections. Conductor crosssectional area: 0.5 to 2.5 mm2
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
