產品內容介紹
A-B 80190-220-01-R控制器
按照以下步驟啟用Datalinks以寫入數據。
1.僅設置所需數量的連續控制器的值，以驅動向驅動器寫入數據所需的數據鏈路包含在網絡I/O連接中。
2.重置選項模塊；參見第49頁重置選項模塊。
3.由于邏輯命令和參考總是用在選項中模塊，配置驅動器中的參數以接受邏輯選項模塊中的命令和引用。當使用通過選項模塊進行速度參考的控制器，在驅動器中設置兩個字段參數545-[Speed Ref A Sel]：
a、 設置驅動器的端口字段（例如，0-PowerFlex 755）。
b、 設置參數字段以指向選項所在的驅動器端口模塊已安裝（對于本例，端口4參考）。
此外，還要驗證驅動器中的掩碼參數（例如，參數324-[Logic Mask]）配置為接收所需的來自選項模塊的邏輯。有關詳細信息，請參閱驅動器文檔。
完成上述步驟后，選項模塊準備接收輸入數據并將狀態數據傳輸?shù)街骺仄鳎刂破鳎?br/>
接下來，配置控制器識別I/O并將其傳輸至選項模塊。見第4章，配置I/O。
啟用數據鏈接以讀取數據
控制器輸入圖像（驅動器到控制器輸入）可以有0到16其他32位參數（Datalinks）。它們是使用主機配置的參數17-[DL To Net 01]至32-[DL-To Net 16]。的數量
當前使用的數據鏈路由控制器中的連接大小控制。看見有關更多信息，請參閱第4章中相應的控制器示例部分設置連接大小。使用ControlLogix控制器和通用配置文件時，配置Datalink參數現在如本節所述。
主機參數17-[DL To Net 01]至32-[DL-To Net 16]配置驅動器、選項模塊或任何其他連接的外圍設備中的哪些參數將值發送到網絡。PowerFlex 20-HIM-A6或20-HIM-C6SHIM、DriveExplorer軟件或DriveExecutive軟件可用于選擇驅動器或外圍設備（按端口號）和參數（按名稱）。作為替補方法，則可以使用以下公式按數字手動設置參數值：To Net參數值=（10000*端口號）+（發起參數號）
例如，假設您想使用主機參數17-[DL to Net 01]來讀取插入驅動器端口6的可選I/O模塊的參數2。使用公式中，主機參數17-[DL To Net 01]的值為（10000*6）+ (2) = 60002.按照以下步驟啟用Datalinks讀取數據。
1.僅將所需數量的連續驅動器的值設置為從驅動器讀取數據所需的控制器數據鏈路包含在網絡I/O連接中。
2.重置選項模塊；參見第49頁重置選項模塊。選項模塊配置為將輸出數據發送到主控制器。
現在必須配置控制器，以識別I/O并將其傳輸?shù)竭x項模塊。參見第4章，配置I/O。
Follow these steps to enable Datalinks
to write data. 1. Set the values of only the required number of contiguous controller-todrive Datalinks needed to write data to the drive and that are to be included in the network I/O connection. 2. Reset the option module; see Resetting the Option Module on page 49. 3. Since the Logic Command and Reference is always used in the option module, configure the parameters in the drive to accept the Logic Command and Reference from the option module. When using the controller for speed reference via the option module, set two fields in drive Parameter 545 - [Speed Ref A Sel]: a. Set the Port field for the drive (for example, 0 - PowerFlex 755). b. Set the Parameter field to point to the drive port in which the option module is installed (for this example, Port 4 Reference). Also, verify that the mask parameters in the drive (for example, Parameter 324 - [Logic Mask]) are configured to receive the desired logic from the option module. See the drive documentation for details. After the above steps are complete, the option module is ready to receive input data and transfer status data to the master (controller). Next, configure the controller to recognize and transmit I/O to the option module. See Chapter 4, Configuring the I/O. Enabling Datalinks To Read Data The controller input image (drive-to-controller inputs) can have 0 to 16 additional 32-bit parameters (Datalinks). They are configured using Host Parameters 17 - [DL To Net 01] through 32 - [DL To Net 16]. The number of Datalinks actively used is controlled by the connection size in the controller. See the respective controller example sections in Chapter 4 for more information on setting the connection size.
When using a ControlLogix controller
and the Generic Profile, configure the Datalink parameters now as described in this section. Host Parameters 17 - [DL To Net 01] through 32 - [DL To Net 16] configure which parameters in the drive, option module, or any other connected peripheral send the values to the network. The PowerFlex 20-HIM-A6 or 20-HIM-C6S HIM, DriveExplorer software, or DriveExecutive software can be used to select the drive or peripheral by port number and the parameter by name. As an alternate method, the parameter value can be set manually by number using this formula: To Net Parameter Value = (10000 * Port Number) + (Origination Parameter Number) For example, suppose you want to use Host Parameter 17 - [DL To Net 01] to read Parameter 2 of an optional I/O module plugged into drive Port 6. Using the formula, the value for Host Parameter 17 - [DL To Net 01] would be (10000 * 6) + (2) = 60002. Follow these steps to enable Datalinks to read data. 1. Set the values of only the required number of contiguous drive-tocontroller Datalinks needed to read data from the drive and that are to be included in the network I/O connection. 2. Reset the option module; see Resetting the Option Module on page 49. The option module is configured to send output data to the master (controller). You must now configure the controller to recognize and transmit I/O to the option module. See Chapter 4, Configuring the I/O.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
